Webgateway (NGINX, HAProxy)

This role provides a stack of components that enables you to serve a web application via HTTP. In addition, you can do load balancing and configure failover support.

Versions

• HAProxy: 2.7.x

• Nginx: 1.24.x

Role architecture

The webgateway role uses:

• the nginx web server

• the HAProxy load balancer and proxy server

We provide basic config for both services. You will have to add custom configuration to serve your site.

Both services support config reload and changing the binary without downtime.

Note

Although we install nginx and HAProxy, there is no need to use them both. Since there is no connection between them w.r.t configuration, you can still use only one of them and leave the other one as is.

How we differ from what you are used to

Here is how we differ from what you already know from common Linux distributions and how you are used to configure, start, stop and maintain these packages.

• configuration file locations:

  We do not edit files in /etc/nginx/* or /etc/haproxy/*, respectively. Since we use NixOS, files have to be edited in /etc/local, followed by a NixOS rebuild which copies them into the Nix store and activates the new configuration. To do so, run the command sudo fc-manage -b

• service control:

  We use systemd to control processes. You can use familiar commands like sudo systemctl restart nginx to control services. However, remember that invoking sudo fc-manage -b is necessary to put configuration changes into effect. A simple restart is not sufficient. For further information, see Local Configuration.

HAProxy

Put your HAProxy configuration in /etc/local/haproxy/haproxy.cfg. You can find an example config at /etc/local/haproxy/haproxy.cfg.example. Please refer to the official documentation for more details.

If you need more than just one centralized configuration file, you can use multiple files named *.cfg in the local configuration directory. They will get merged along in alphabetical order.

Changes to your custom config will cause haproxy to reload without downtime on the next fc-manage run.

The final haproxy config file can be shown with: haproxy-show-config.

nginx

We provide basic config. You have to configure at least one virtual host.

Changes to your custom config will cause nginx to reload without downtime on the next fc-manage run if the config is valid. It will display a warning if invalid settings are found in the nginx config.

Note that changes to listen directives that are incompatible with the running config may require a manual Nginx restart that drops connections. Using reuseport can avoid such situations (see below).

After building it with sudo fc-manage -b, the final nginx config file can be shown with: nginx-show-config

You can check if the config is valid with: nginx-check-config. The script also warns about potential security issues with your current config.

The recommended method is structured configuration via Nix code as described in the next section. We still support plain nginx config and structured JSON config in /etc/local/nginx.

Structured Nix Configuration (recommended)

Define Nginx virtual hosts with the NixOS option flyingcircus.services.nginx.virtualHosts.

See Custom NixOS-native configuration for general information about writing custom NixOS modules in /etc/local/nixos.

The following NixOS module defines two virtual hosts listening on all frontend IP addresses which is the default. Requests to Port 80 are redirected to 443 which serves SSL using a managed certificate from Let’s Encrypt. subdomain.example.com/internal is protected by HTTP Basic Auth with an users file automatically created for users with the login permission:

# /etc/local/nixos/nginx.nix
{ ... }:
{
  flyingcircus.services.nginx.virtualHosts = {
    "www.example.com"  = {
      serverAliases = [ "example.com" ];
      default = true;
      forceSSL = true;
      root = "/srv/webroot";
    };

    "subdomain.example.com"  = {
      forceSSL = true;
      extraConfig = ''
        add_header Strict-Transport-Security max-age=31536000;
        rewrite ^/old_url /new_url redirect;
        access_log /var/log/nginx/subdomain.log;
      '';
      locations = {
        "/cms" = {
          # Pass request to HAProxy, for example
          proxyPass = "http://localhost:8008";
        };
        "/internal" = {
          # Authenticate as FCIO user (user has to have login permission).
          basicAuth = "FCIO user";
          basicAuthFile = "/etc/local/htpasswd_fcio_users";
          proxyPass = "http://localhost:8008";
        };
      };
    };
  };
}

You can also find this example at /etc/local/nixos/nginx.nix.example if the webgateway role is enabled.

Our flyingcircus.services.nginx.virtualHosts option supports all settings of the upstream NixOS option services.nginx.virtualHosts with the difference that we bind to all frontend IPs by default instead of all interfaces.

flyingcircus.services.nginx.virtualHosts has the following custom settings:

• emailACME: set the contact address for Let’s Encrypt (certificate expiry, policy changes), defaults to none.

• listenAddresses: List of IPv4 and quoted IPv6 addresses to bind to (default: frontend IPs).

The listen option overrides our defaults: the listenAddresses options has no effect and no IP is used automatically in this case.

One vhost definition should set the default option. Without that, the first vhost entry will be the default one. Because we combine config from multiple files, setting an explicit default is strongly encouraged to avoid surprises with server name matching.

We support a custom reuseport option for listen which is true by default. The option only has an effect on the default vhost and is ignored on others. The effect is that Nginx will start a separate socket listener for each worker. This helps performance and allows changing listen IPs on config reload without the need to restart Nginx.

Deprecated options:

• listenAddress: Single IPv4 address

• listenAddress6: Single IPv6 address

listenAddresses should be used instead.

If only one of the listenAddress* options is given, the vhost listens only on IPv4 or IPv6. If none of the listenAddress* options is given, all frontend IPs are used. Using listenAddresses at the same time overrides the deprecated options.

HTTPS and Let’s Encrypt

For SSL support with redirection from HTTP to HTTPS, use forceSSL. Let’s Encrypt (enableACME) is activated automatically if one of forceSSL, onlySSL or addSSL is set to true. Self-signed certificates are created for new vhosts before Nginx starts or reloads. They are replaced by the proper certificates after some seconds. A systemd timer checks the age of the certificates and renews them automatically if needed. To use a custom certificate, set the certificate options and set "enableACME" = false.

SSL ciphers

With default settings, the following ciphers are available:

TLS 1.3:

• TLS_AES_128_GCM_SHA256

• TLS_AES_256_GCM_SHA384

• TLS_CHACHA20_POLY1305_SHA256

TLS 1.2:

• TLS_ECDHE_ECDSA_WITH_AES_128_GCM_SHA256

• TLS_ECDHE_ECDSA_WITH_AES_256_GCM_SHA384

• TLS_ECDHE_ECDSA_WITH_CHACHA20_POLY1305_SHA256

To use ciphers based on RSA for legacy clients, an RSA key must be used for the certificates. Note that this disables the ciphers listed above and reduces performance with newer clients.

Overriding the key type can be done per certificate:

security.acme.certs."test.fcio.net".keyType = "rsa2048";

Using two certificates to support both kinds of ciphers is possible with Nginx but needs manual configuration.

For ciphers using DHE, an RSA certificate must be used. dhparams must be generated and set:

security.dhparams.params.nginx = {};
services.nginx.sslDhparam = config.security.dhparams.params.nginx.path;

This enables the following TLS 1.2 ciphers:

• TLS_DHE_RSA_WITH_AES_128_GCM_SHA256

• TLS_DHE_RSA_WITH_AES_256_GCM_SHA384

The DH param file is located at /var/lib/dhparams/nginx.pem. This path can be referenced from Nix code by security.dhparams.params.nginx.path as shown in the config example above.

The services.nginx.sslCiphers option can be used to change the cipher list.

If you enable weaker ciphers, you should also set services.nginx.legacyTlsSettings to true and services.nginx.recommendedTlsSettings to false.

This sets ssl_prefer_server_ciphers on so better ciphers at the beginning of the cipher list are used if possible.

Plain Configuration (old)

If you want to use plain Nginx configuration add the config file as /etc/local/nginx/nginx.conf. It has to contain at least one server block declaration as described in the official documentation. Your files will then be integrated with our nginx base config. Therefore, please omit the http clause. It is already set by the base config.

See /etc/local/nginx/example-configuration for an example and /etc/local/nginx/README.txt.

JSON Configuration (old)

Although not recommended anymore, JSON config can be added to /etc/local/nginx, alongside with plain nginx config files. Nix config should be used instead, as described above. JSON config supports the same options as Nix config so converting from JSON to Nix is basically just a syntax change.

See /etc/local/nginx/README.txt for an example and more info.

Logging

nginx’ access logs are stored by default in /var/log/nginx/access.log. Individual log files for virtual hosts can be defined in the corresponding configuration sections. We use the anonymized log format for GDPR conformance by default.

Add this to an extraConfig block in Nix config or your plain nginx config:

access_log /var/log/nginx/app.log;

nginx’ error logs go to systemd’s journal by default. To view them, use journalctl(1) as usual, e.g.:

$ journalctl --since -1h -u nginx

Basic auth with legacy password hashes

Starting with NixOS 23.05, nginx uses a version of libxcrypt which only supports algorithms marked as strong. You will encounter errors when password files for HTTP basic auth use algorithms like MD5 (hash prefix$1$) and SHA256 ($5$). Password hashes using these algorithms should be replaced as soon as possible.

If you still need them on 23.05, use the Nginx package which still supports all algorithms:

# /etc/local/nixos/nginx-legacy-crypt.nix
{ pkgs, ... }:
{
  services.nginx.package = pkgs.nginxLegacyCrypt;
}

A package alias under the name nginxLegacyCrypt is already available in our NixOS 22.11 release, enabling seamless platform upgrades with the same configuration.